Definition and Types of Pattern

-

 Pattern:
Pattern is that the replica of the device which is that the output of casting process. This when molded in sand forms mold. After filling mold with the molten metal there's a formation of casting. Patterns play a really important role in casting as they decide the standard also as perfection during a particular casting process. Gates and runners are the foremost important components in several sorts of pattern. Pattern is that the basic requirement for creation of mold and it's always bigger than the dimensions of casting. There should be a correct selection of pattern so it must be ready to sustain rough handling. It forms mold cavity for casting processes. The patterns could also be made from metals like aluminum, brass, plaster and wax.

  Sorts of Patterns:

 Types of Pattern



 Following are the common sorts of patters:
1. Single piece pattern
2.  Split pattern
3. Gated pattern
4. Multi piece pattern
5. Match plate pattern
6. Skeleton pattern
7. Sweep pattern
8. Lose piece pattern
9. Follow board pattern
10. Cope and drag pattern
11. Segmental pattern and
12. Shell pattern




Comments

Post a Comment

Popular posts from this blog

Definition and Parts of a Vernier Caliper

-
Image
Vernier Caliper and Its Parts:   Vernier Caliper Vernier Caliper: The vernier caliper is a measuring tool wont to get precise linear dimension measurements. A vernier micrometer is particularly useful to live the diameter of cylindrical objects as its jaws can clamp either side to urge accurate measurements. Main Parts of a Vernier caliper:   1. Upper Jaws or Inside Jaws   2. Lower Jaws or Outside Jaws 3. Depth Rod   4. Main Scale 5. Vernier Scale 6. Lock Screw 7. Thumb Screw 1. Upper Jaws or Inside Jaws: The upper jaws are smaller in size and are attached to the upper portion of the vernier micrometer. Similar to the lower jaws, one of these jaws is fixed and the other is movable. The difference between them and the lower jaws is that the upper jaws are used for measuring inside dimensions of hollow objects such as inside diameters of pipes, lengths and widths of boxes etc. The jaws are placed inside the place to be measured and then opened
Read more

Lathe Machine Operations

-
Image
    Lathe Operations: 1.      Facing: It is an operation of reducing the length of the workpiece by feeding the perpendicular to the lathe axis. This operation of reducing a flat surface on the end of the workpiece. For this operation, regular turning tool or facing tool may use. The cutting edge of the tool should set to the same height as the centre of the workpiece. 2.      Turning: It is the most common type of operation in all lathe machine operations. Turning is the operation of removing the excess material from the workpiece to produce a cylindrical surface to the desired length. The job held between the centre or a chuck and rotating at a required speed. The tool moves in a longitudinal direction to give the feed towards the headstock with proper depth of cut. The surface finish is very good.    Ø Straight Turning: The workpiece is held on the chuck and it is made to rotate about the axis, and the tool is fed parallel to the lathe axis. The straight turning
Read more

Micrometer and it's main parts

-
Image
Micrometer and It's Parts:  Micrometer   Micrometer: The micrometer may be a precision measuring system, employed by engineers. Each revolution of the rachet moves the spindle face 0.5mm towards the anvil face. The object to be measured is placed between the anvil face and the spindle face. The rachet is turned clockwise until the thing is ‘trapped’ between these two surfaces and therefore the rachet makes a ‘clicking’ noise. This means that the rachet can't be tightened anymore and therefore the measurement are often read.   Main Parts of Micrometer: 1.      Main Frame 2.      Zero adjusts screw 3.      Anvil 4.      Spindle 5.      Anvil Face and Spindle Face 6.      Lock Nut 7.      Sleeve 8.      Thimble 9.      Rachet 1.      Main Frame: It’s a c shaped frame as identified within the figure, may be a rigid part that has both holding points for employment or object to be measured. Its size depends on micrometer measuring range so
Read more